errors.lir

000082
[937]Size of fft larger than 65536.
Could be caused by some bug related to the use of fft1 version 6
Change fft1 version manually in the parameter file for the current
receive mode.
[999]Code in cwdetect.c not yet written.
[1000]routine:open_rx_sndin   file:lsetad.c
Routine to open audio input is called but audio_flag says 
input is already open. 
[1001]routine:open_rx_sndin   file:lsetad.c
The selected output device does not respond. Try another.
[1002]routine:get_buffers        file:buf.c
Routine to allocate memory is called but buffers_flag says
memory is already allocated.    
[1003]Failed to allocate scratch memory.
[1004]Failed to allocate scratch memory.
[1005]routine:close_audio_input   file:lsetad.c
Error when closing device. 
[1006]routine:close_rx_sndout   file:lsetad.c
Close failed on Rx output from soundcard.
[1007]routine: open_rx_sndin     file:lsetad.c
Failed to open audio input.
Check sound system !!!
(If OSS is used, start sound with the soundon command.)
Maybe setup file "dsp_uiparm" is incorrect ?
Use U = A/D and D/A setup in main menu.
 (do not forget W = save afterwards to make a new "dsp_uiparm" file)
[1008]routine:open_rx_sndin  file:lsetad.c                      
call to ioctl failed. (SNDCTL_DSP_SETFRAGMENT)
[1009]routine: open_rx_sndin     file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_CHANNELS)
[1010]routine: open_rx_sndin     file:lsetad.c
Could not set desired no of channels for A/D input !!!
Use U = A/D and D/A setup in main menu.
 (do not forget W = save afterwards to make a new "dsp_uiparm" file)
[1011]routine: open_rx_sndin     file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_SPEED)
[1012]routine: open_rx_sndin     file:lsetad.c
A/D sampling speed could not be set to desired value (new A/D board )
Initialise sound board properly or use U = A/D and D/A setup in main menu.
 (do not forget W = save afterwards to make a new "dsp_uiparm" file)
[1013]routine: open_rx_sndin     file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_SETFMT)
[1014]routine: open_rx_sndin     file:lsetad.c
Could not set little endian format for 16 or 24 bit audio input.
[1015]routine:open_audio_output  file:lsetad.c                      
Routine to open audio output is called but audio_flag says 
output is already open. 
[1016]routine:set_analog_io      file:lsetad.c
Unable to create/open log-file in write mode.
Make sure the file soundboard_init.log does not have incorrect attributes.
(or better, remove the old file)  
[1017]routine:open_audio_output  file:lsetad.c
Could not open device for audio output.
Use U = A/D and D/A setup in main menu to select proper drivers.
 (do not forget W = save afterwards to make a new "dsp_uiparm" file)
[1018]routine:open_audio_output  file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_SETFRAGMENT)
[1019]routine:open_audio_output  file:lsetad.c
call to ioctl failed . (SNDCTL_DSP_CHANNELS)
[1020]routine:open_audio_output  file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_SETFMT)
[1021]routine:open_audio_output  file:lsetad.c
Could not open D/A with the specified no of bits.
Probable cause is use of setup parameters from different hardware.
Try to set sound board parameters (U in main menu).
[1022]routine:open_audio_output  file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_SPEED)
[1023]routine:open_audio_output  file:lsetad.c
Sound card reports unexpected speed value (more than 5% off).
Probable cause is use of setup parameters from different hardware.
Try to set sound board parameters (U in main menu).
More info in the log file: soundboard_init.log
If you are using automatic startup, disable it by editing
the text file par_userint:
Set Autostart [0]
[1024]routine:set_analog_io      file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_SPEED)
[1025]routine:open_audio_output  file:lsetad.c
Failed to allocate write buffer
[1026]routine:close_rx_sndout   file:lsetad.c                      
call to ioctl failed. (SNDCTL_DSP_RESET)
[1027]routine:set_analog_io      file:lsetad.c                      
Failed to set no of channels (should never happen)
[1028]routine:set_analog_io      file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_GETISPACE)
[1029]Failed to open/create the file par_userint or the file par_network.
[1030]Failed to allocate scratch memory.
[1031]Failed to allocate scratch memory.
[1032]file:fft0.c
Failed to allocate scratch memory.
Make more memory available.
[1033]Failed to allocate scratch memory.
[1034]routine: set_vgamode      file:lsys.c      
Failed to allocate scratch memory.
Make more memory available.
[1035]Failed to allocate scratch memory.
[1036]routine: init_wide_graph      file:wide_graph.c      
Failed to allocate memory for waterfall graph.
Make more memory available.
[1037]routine:set_analog_io      file:lsetad.c
Could not close audio device while testing all possible drive routines.
[1038]routine:set_analog_io      file:lsetad.c
Could not open audio device selected for input.
[1039]routine:set_analog_io      file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_CHANNELS)
[1040]routine:set_analog_io      file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_SPEED)
[1041]routine:set_analog_io      file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_SPEED)
[1042]routine:set_analog_io      file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_SETFMT)
[1043]routine:set_analog_io      file:lsetad.c
Could not set no of channels.
[1044]Failed to allocate scratch memory.
[1045]routine:set_analog_io      file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_GETISPACE)
[1046]routine: test_rx     file:rxtest.c
Fonts too large for current screen.
Try larger screen or smaller fonts.
[1047]Failed to allocate scratch memory.
[1048]Failed to allocate scratch memory.
[1049]Failed to allocate scratch memory.
[1050]routine: make_symfit   file:calsub2.c
Could not fit polynomial to data.
Clear old correction function and try less steep desired spectrum. 
[1051]routine: llsq          file:llsq.c
llsq called with too many parameters (programming error)
[1052]routine: init_fft1_filtercorr   file:fft1.c
Error in file dsp_xxx_corr. 
Remove file and make a new file by running the calibration routine.
[1053]routine: init_foldcorr   file:fft1.c
Error in file dsp_xxx_iqcorr.
Remove file and make a new file by running the calibration routine.
[1054]routine: cal_update_ram   file:calsub2.c
Failed to find parameters for old desired spectrum.
Probably error in dsp_xxx_iqcorr.
Use Z to clear in ram, then S to save cleared uncorrupted data
in a new dsp_xxx_iqcorr file.
[1055]Failed to allocate scratch memory.
[1056]routine: init_baseband_graph      file:baseband_graph.c      
Failed to allocate memory for baseband graph.
Try to reduce baseband storage time.
Edit parameter file par_wcw, par_cw, par_hsms....
You may also try narrower baseband filter or smaller storage
times for fft1 or fft2. 
[1057]routine:set_fft1_endpoints       file:fft1.c
The calibration curve uses far too small part of the spectrum.
Calibration error or excessive oversampling.
Set sampling speed lower, make desired response wider
or reduce steepness of desired frequency response.
You may have to remove the file dsp_xxx_corr (xxx for current rx mode)
[1058]Output can not start.

(1)The parameter "Output delay margin (ms)" may be too small.
Try to set it large, like 1000 for a whole second.
If this helps, use 'T' to find out by how much you can reduce it.
The D/A MIN value should be about 20 milliseconds, if you see something
much larger, reduce the Output delay margin by the value minus 20 ms.
It may be necessary to repeat a couple of times until you find
MIN near 20.
Note that the MIN value should be evaluated after a couple of
minutes.

(2)Your CPU could be overloaded. Maybe you are trying to use
filter and decimation in the time domain with a large fft3?
Select filter/decimation in the frequency domain. '1' in the
box in the upper right corner of the baseband spectrum.

(3)You might have too demanding parameters for the wideband
processing. Use 'T' to find out how the different threads load 
your CPU(s)

(4)The parameter "Max DMA rate" could be set too low.

If the above does not help, please send a mail to leif@sm5bsz.com
[1059]routine: init_fft1_filtercorr   file:fft1.c
The save file is corrupted. Can not process old data.
Probable cause: Incorrect calibration file.
Data was probably saved in uncalibrated mode while calibration was
present on disk for another sampling rate or input mode.
[1060]routine: init_foldcorr          file:fft1.c
The save file is corrupted. Can not process old data.
[1061]routine: init_blanker      file:buf.c      
Failed to allocate memory for noise blanker.
[1062]Calibration file disappeared or became corrupted between program 
start and attempt to save raw data in a file or request for calibration 
from the network.
[1063]Permission to use the parallel port denied.
The use of ioperm() or iopl() requires root privileges.
[1064]Access to parallel port denied.
Make sure inpout32.dll is available to Linrad. 
[1065]Call to alsa_get_dev_native_capabilities() failed.
This should never happen!!
[1066]routine: init_baseband        file:baseband_graph.c
Failed to allocate memory for baseband. 
Try shorter baseband storage time, narrower bandwidth or 
reduce size of earlier processing stages. 
(Could also be an attempt to allocate too many arrays, 
MAX_BASEB_ARRAYS too small)
You may have to remove the par_xxx file (par_wcw, par_ssb,...) 
[1067]routine:set_analog_io      file:lsetad.c
Failed to close audio device while testing all possible drive routines.
[1068]routine:set_analog_io      file:lsetad.c
Failed to open audio device for output while input is open.
[1069]routine:set_analog_io      file:lsetad.c                      
Could not set no of output channels to 1 or 2
[1070]The pilot tone prestart parameter in the soundcard setup 
for the TX is too large. Use 'V=TX mode setup' in the main menu, 
then 'B=Soundcard setup for Tx.' to set a smaller value.
(Or edit par_userint: 'Tx pilot microsec.')

If you really want a larger prestart, change CW_MAX_TIME_CONSTANT
which is located in txdef.h.
[1071]routine:set_analog_io      file:lsetad.c                      
call to ioctl failed. (SNDCTL_DSP_GETFMTS)
[1072]routine:set_analog_io      file:lsetad.c                      
call to ioctl failed. (SNDCTL_DSP_SPEED)
[1073]routine:set_analog_io      file:lsetad.c                      
call to ioctl failed. (SNDCTL_DSP_SPEED)
[1074]Failed to set thread blocking rxout to idle state. file:rxout.c
[1075]routine:read_eme_database      file:eme.c                      
Failed to get scratch memory.
[1076]The timing for the rise time or for the pilot tone
prestart is out of limits. Use 'V=TX mode setup' in the main menu.
[1077]Failed to get buffer space from the soundcard device.
Unknown reason - should never happen.
[1078]Failed to get scratch memory.
[1079]routine: open_tx_output     file:lsetad.c
Failed to open audio output for tx.
Check sound system !!!
(If OSS is used, start sound with the soundon command.)
Maybe setup file "dsp_uiparm" is incorrect ?
Use U = A/D and D/A setup in main menu.
 (do not forget W = save afterwards to make a new "dsp_uiparm" file)
[1080]The file par_perseus is corrupted. 
Use "U=A/D and D/A setup for RX" in the main menu to create a new file.
[1081]routine:pc_radio    file:main.c                      
failed to get small scratch memory
[1082]routine:init_wide_graph    file:wide_graph.c                      
failed to get small scratch memory
[1083]USB I/O Error: unable to download the Perseus firmware to 
the FX2 controller: USB IO error. 
Exit and restart Linrad without moving the USB connector. 
This error is normal with USB3 under Windows 10 the first time a Perseus
is connected (or after a reboot.) 
If you see this error a second time, try to move to another USB
connector and try to start Linrad again. Be prepared you might
have to start twice.
Once Linrad starts properly the second time you can start and stop
at without seeing this error.
[1084]USB I/O Error: unable to download the Perseus firmware to 
the FX2 controller. Firmware file not found. Make sure you have
the appropriate perseusxxxx.sbs file in your C:\Linrad\dll directory.
[1085]USB I/O Error: unable to download the Perseus firmware to 
the FX2 controller. Invalid HEX Record.
[1086]routine:open_audio_output  file:lsetad.c
Could not open device for audio output.
[1087]Failed to open file for saving calibration data.
[1088]routine:set_analog_io      file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_GETISPACE)
[1089]USB I/O Error: unable to download the Perseus firmware to 
the FX2 controller. Invalide Extended HEX Record
[1090]USB I/O Error: unable to download the Perseus firmware to 
the FX2 controller. Unknown error.
[1091]Sampling rate in par_userint not compatible with Perseus setup.
Rerun "U=A/D and D/A setup for RX" from the main menu.
[1092]Unable to program the Perseus FPGA:
FPGA bitstream file not found.
Make sure the appropriate perseusxxxxx.sbs file is present 
in the the same directory where your perseususb.dll file is placed.
Currently the files are:
 perseus48k24v31.sbs
 perseus95k24v31.sbs 
 perseus96k24v31.sbs
 perseus125k24v21.sbs
 perseus192k24v31.sbs
 perseus250k24v21.sbs
 perseus500k24v21.sbs
 perseus1m24v21.sbs
 perseus1d6m24v21.sbs 
 perseus2m24v21.sbs

You can fix this problem by running the latest 
setup-linrad-perseus-bin-package which is available here:
http://sm5bsz.com/linuxdsp/linrad.htm 
[1093]routine:set_analog_io   file:lsetad.c                      
call to ioctl failed. (SNDCTL_DSP_GETISPACE)
[1094]routine:set_analog_io   file:lsetad.c                      
call to ioctl failed. (SNDCTL_DSP_GETISPACE)
[1095]routine:set_analog_io   file:lsetad.c                      
call to ioctl failed. (SNDCTL_DSP_GETISPACE)
[1096]Unable to program the Perseus FPGA: USB IO Error
Check USB connection and retry.
[1097]Unable to program the Perseus FPGA: Unknown error.
[1098]Unexpected error: 
Unable to start input with PerseusStartAsyncInput API.
[1099]routine:open_audio_output      file:lsetad.c                      
Could not set no of channels for output.
[1100]Failed th get the expected name string from the Perseus.
[1101]Network write failed.
[1102]routine:set_analog_io      file:lsetad.c
Could not open audio device selected for input.
[1103]routine:init_spur_spectra   file:spur.c                      
Failed to allocate scratch memory. Try smaller fft sizes or
smaller storage times. 
[1104]File name too long in adfile or adwav.
[1105]routine:complex_lowpass      file:spur.c                      
Internal error. Please report this bug!!!
[1106]routine:make_afc_graph    file:afc.c
Failed to allocate memory for afc.
Try smaller frequency drift and/or smaller frequency lock range and/or
smaller averaging times for transforms and/or afc.
[1108]Unrecoverable EPIPE error on ALSA input.
[1109]routine:open_rx_sndin     file:lsetad.c                      
call to ioctl failed. (SNDCTL_DSP_GETISPACE)
Try to select "Close and reopen output" in the soundcard setup.
[1110]routine: init_foldcorr  file:fft1.c
Could not allocate memory for temporary buffers.
[1111]routine: write_wav_header    file:modesub.c
Failed to position .wav file.
[1112]routine: write_wav_header    file:modesub.c
Failed to write .wav file header.
[1113]ALSA:thread rx_adinput/readi error.; 
[1114]routine: write_wav_header    file:modesub.c
Failed to get position position for .wav file start.
[1115] file:main.c
File name for mode parameter file too long in adfile or adwav.
[1116]Failed to write to calibration file.
[1117]lir_empty_da_device_buffer/writei:
Can't recover from underrun, prepare failed.
[1118]routine: select_namlin    file:modesub.c
Failed to get position for adwav or adfile start.
[1119]routine: select_namlin    file:modesub.c
Failed to set position for adwav or adfile.
[1120]routine: get_parfile_name    file:modesub.c
Parameter file has the same name as the data file. 
This would cause incorrect data when parameters are saved.
Change in adfile or adwav!!
[1121]routine:init_eme_database      file:eme.c                      
Failed to create file for own location.
[1122]routine:init_eme_database      file:eme.c                      
Failed to read allcalls.dta. Excessive line length.
[1123]routine:init_eme_database      file:eme.c
Too many DX stations in database. Increase MAX_DXCALLS.
[1124]routine:init_eme_database      file:eme.c                      
Failed to read dir.skd  Excessive line length or field too long.
[1125]Too many devices for SDR-14 and/or SDR-14
Read soundboard_rx_init.log 
If you want more devices, change MAX_SDR14_DEVICES in lsdr.c
[1126]ALSA:thread tx_adinput: short readi.
[1127]Unknown read error reported by ALSA. 
[1128]routine:init_eme_database      file:eme.c                      
Failed to create file for dx database.
Make sure the directory /home/emedir exists and that you
have permission to write to it.
Linrad will look for these files:
/home/emedir/allcalls.dta
/home/emedir/eme.dta
/home/emedir/dir.skd
Download them from the Internet.
[1129]routine:init_eme_database      file:eme.c
Something went wrong in the eme database creation.
This is a bug of some kind.
[1130]routine:init_eme_graph       file:eme.c
Auto init of eme data was specified, but the dx database
file is missing. Even if empty, it should be present.
Create a new one with "M" in the main menu.
[1131]routine:init_eme_graph       file:eme.c
The eme database file is incorrect.
Create a new one with "M" in the main menu.
[1132]routine:init_eme_graph       file:eme.c
Not enough memory to install eme database.
[1133]routine:init_eme_database      file:eme.c
Failed to create error report file for dx database.
Make sure the directory /home/emedir exists and that you 
have permissions to write to it.
[1134]routine:set_analog_io         file:lsetad.c
Failed to set input sampling speed.
The device driver is incorrect and the usual work around
was not sucessful.
Check the log file: soundboard_init.log for details
[1135]routine:set_analog_io      file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_SPEED)
[1136]routine:memalloc  routine modesub.c
memalloc was called while memalloc_no had a value outside
the range set by memalloc_max.
[1137]routine:remove_iq_notch     file:calsub2.c
Not enough data points to fit. Reduce IQ_FIT_MINFREQ
Make sure to have a PRF well below the new value when collecting
phase and amplitude functions with the pulse generator.
[1138]routine:set_analog_io      file:lsetad.c
Failed to close audio device while testing all possible drive routines.
[1139]routine:set_analog_io      file:lsetad.c
No device found for analog output.
[1140]lir_rx_dawrite/writei: 
Can't recover from underrun. prepare failed.
[1141]Failed to allocate scratch memory.
[1142]Failed to allocate scratch memory.
[1143]Failed to allocate scratch memory.
[1144]Failed to open file for saving calibration data.
[1145]Failed to write data to calibration file.
[1146]Could not open soundcard device for input:MMSYSERR_BADDEVICEID
Specified device identifier is out of range.
[1147]Could not open soundcard device for input: MMSYSERR_NODRIVER
No device driver is present.
[1148]The soundcard buffer for Tx output has a size that
is not as power of two. The parameter for max DMA rate
is probably too small.
[1149]The soundcard buffer for Tx microphone input has a size that
is not as power of two. The parameter for max DMA rate
is probably too small.
[1150]Failed to open the RX loudspeaker output.
ALSA does not accept the device number in your setup or the
number of channels, bytes or the device speed is inconsistent.
Read z_ALSA.txt for info about ALSA setup.
Run "U=A/D and D/A setup for RX" in the main menu to
correct the problem by re-selecting the loudspeaker output.
[1151]Failed to open the TX output.
ALSA does not accept the device number in your setup or the
number of channels, bytes or the device speed is inconsistent.
Read z_ALSA.txt for info about ALSA setup.
Run "V=TX mode setup" in the main menu to correct the problem 
by re-selecting the TX output. (B on the sub-menu)
[1152]Failed to open the RX soundcard input.
ALSA does not accept the device number in your setup or the
number of channels, bytes or the device speed is inconsistent.
Read z_ALSA.txt for info about ALSA setup.
Run "U=A/D and D/A setup for RX" in the main menu to
correct the problem by re-selecting the soundcard input.
[1153]Failed to open the TX microphone input.
ALSA does not accept the device number in your setup or the
number of channels, bytes or the device speed is inconsistent.
Read z_ALSA.txt for info about ALSA setup.
Run "V=TX mode setup" in the main menu to correct the problem 
by re-selecting the TX microphone input. (B on the sub-menu)
[1154]Failed to open the RX loudspeaker output.
ALSA does not accept the device number in your setup or the
number of channels, bytes or the device speed is inconsistent.
Read z_ALSA.txt for info about ALSA setup.
Run "U=A/D and D/A setup for RX" in the main menu to
correct the problem by re-selecting the loudspeaker output.
[1155]Could not open soundcard device for input: MMSYSERR_NOMEM
Unable to allocate or lock memory.
[1156]Could not open soundcard device for input: WAVERR_BADFORMAT
Attempted to open with an unsupported waveform-audio format.

If this happens on a Windows 10 system on which you have a Delta 44 you have 
to reconfigure the Delta 44. (Reboot or power off does not help.)
Use the M-Audio Delta Control Panel to set the sampling rate to 44100 Hz.
Then use U = A/D and D/A setup in the main menu to select Portaudio
for the soundcard with the ASIO or the WDM-KS driver.

You can select sampling rate, number of channels and number of bits freely.
according to your preferences. The Delta 44 is not locked to 44100, it just
has to inform Windows 10 that it is the default rate.
[1157]Inconsistent soundcard parameters for Windows Rx input.
Number of bits=24, but flag says do not use extended format.
Use 'U' on the main menu to set proper parameters for
your soundcard.
[1158]routine pc_radio         file:main.c
Tx test available only when reading from A/D converter. 
This is an error exit indicating read/write on network or disk.
Use Tx test only from main menu with network disabled.
[1159]The screen is not wide enough to allow spectra with a
resolution of 2.4 khz at the current sampling rate.
This mode requires 4 pixels (or more) over 2.4 kHz so the maximum
bandwidth for the input signal is screen width/4 in kHz. 
Reduce the hardware sampling speed or get a wider screen.
[1160]routine txtest_init       file:txtest.c
2.4 kHz window for txtest spectra too small.
Remove or edit par_txtest_wg.
Txtest will work on wideband systems only.
[1161]The number of points in the calibration data is too small.
Remove the file dsp_xxx_corr and calibrate your system again.
(xxx is the receive mode: wcw, cw, ssb etc.)
[1162]Calibration data is zero.
[1163]The SDR-14 or SDR-IQ failed to start.
Unplug the unit from DC power and try again.
In case this error repeats, check the parameter file par_sdr14
or make a new parameter file by use of U=A/D and DA set up for Rx.
in the main menu.
[1164]Could not open parameter file.
Probably adfile or adwav specified a non-existing directory.
Could also be disk full or something about permissions.
[1165]The sampling speed for the SDR-14 or SDR-IQ is far too high.
Use "U=A/D and D/A set up for Rx" in the main menu.
(If you edited par-sdr14 you might correct your mistake in the file.)
[1166]Portaudio reports an error.
[1167]The RX loudspeaker output thread did not reach its idle state.
(see wcw.c and menu.c)
[1168]Failed to close Portaudio Rx output.
[1169]Input/output error reported by ALSA.
Your soundcards may have changed their numbers.
Read z_ALSA.txt to find out how to give permanent numbers to your
different soundcards.
[1170]The file par_sdrip is corrupted. 
Use "U=A/D and D/A setup for RX" in the main menu to create a new file.
[1171]Failed to allocate scratch memory.
[1172]routine:set_analog_io      file:lsetad.c
Could not open second device for input.
[1173]routine:close_audio_input   file:lsetad.c
Error when closing second input device. 
[1174]routine: open_rx_sndin     file:lsetad.c
Failed to open second device for audio input.
[1175]routine:open_rx_sndin  file:lsetad.c                      
Second A/D input device.
call to ioctl failed. (SNDCTL_DSP_SETFRAGMENT)
[1176]routine: open_rx_sndin     file:lsetad.c
Second A/D input device.
call to ioctl failed. (SNDCTL_DSP_SETFMT)
[1177]routine: open_rx_sndin     file:lsetad.c
Second A/D input device.
Could not set little endian format for 16 or 24 bit audio input.
[1178]routine: open_rx_sndin     file:lsetad.c
Second A/D input device.
call to ioctl failed. (SNDCTL_DSP_CHANNELS)
[1179]routine: open_rx_sndin     file:lsetad.c
Second A/D input device.
Could not set desired no of channels for A/D input !!!
[1180]routine: open_rx_sndin     file:lsetad.c
Second A/D input device.
call to ioctl failed. (SNDCTL_DSP_SPEED)
[1181]routine: open_rx_sndin     file:lsetad.c
A/D sampling speed could not be set to the same value
for the second device.
[1182]routine: set_analog_io     file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_GETCAPS)
[1183]routine: open_rx_sndin     file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_SETTRIGGER)
[1184]routine: open_rx_sndin     file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_SETTRIGGER)
[1185]routine:set_analog_io      file:lsetad.c
call to ioctl failed. (SNDCTL_DSP_CHANNELS)
[1186]routine:set_analog_io      file:lsetad.c                      
Failed to set no of channels (should never happen)
[1187]routine:txtest             file:txtest.c
Failed to allocate memory for oscilloscope function.
Try smaller fft2_storage time.
[1188]Failed to allocate scratch memory.
[1189]Insufficient allocation for Morse decode routine.
Increase parameter MAX_CW_PARTS in sigdef.h
[1190]Failed to create par_wse.
[1191]routine:open_audio_output  file:lsetad.c
Could not open device for audio output.
Check sound system !!!
(If OSS is used, start sound with the soundon command.)
Maybe setup file "dsp_uiparm" is incorrect ?
Use U = A/D and D/A setup in main menu.
 (do not forget W = save afterwards to make a new "dsp_uiparm" file)
[1192]Failed to open Rx A/D input from soundcard. MMSYSERR_ALLOCATED:
Device already allocated.
[1193]Failed to get Perseus product ID.
[1194]Failed to configure Perseus FPGA. 
[1195]Failed to start asynchronous input from the Perseus.
[1196]Could not get sampling rates for Perseus. Error in libperseus-sdr.
[1197]The blocking rx output thread did not respond in time. file:rxout.c
[1198]routine: init_fft1_filtercorr   file:fft1.c
The save file is corrupted. Can not process old data.
Probable cause: Incorrect calibration file.
Data was probably saved in uncalibrated mode while calibration was
present on disk for another sampling rate or input mode.
[1199]You have selected to not use the first perseus.
Go to the directory where you have the parameters for this Perseus unit.
[1200]OSS or alsa-oss is selected for the soundcards.
The Linrad configure script failed to locate the sound devices
/dev/dsp or /dev/sound/dsp
Your system is probably not configured for the OSS API.
There are two alternatives:

1) Configure OSS and run ./configure followed by make. 
   The device files /dev/dsp or /dev/sound/dsp have to be present.

   If you use alsa-oss, the modules snd-mixer-oss and snd-pcm-oss
   have to be inserted to create the device files.
   Commands in the below order:
   modprobe snd-mixer-oss
   modprobe snd-pcm-oss 
   (./configure and make need to be run afterwards)

   If you use 4Front OSS, the device files should be present
   automatically.

2) Change to native ALSA. ('Y' on the RX setup menu.)
   The 'Y' option will not be present in case configure showed a 
   line "MISSING: libasound.so (or headers)"
   You must then install the ALSA development package.
   Run ./configure --with-help for info

This error may occur if native ALSA is not available. Then the second
alternative would not be available. In that case, run configure --with-help
to find out what is needed to get ALSA running or install 4Front OSS.
[1201]Failed to create a thread for the main menu.
[1202]The calibration file is corrupted. Remove the appropriate
dsp_xxx_iqcorr file and make a new calibration for the mirror
image suppression.
[1203]lir_sem_free called for an unitiated semaphore.
[1204]lir_sem_init called for an already initiated semaphore.
[1205]Failed call: ioctl(audio_out,SNDCTL_DSP_RESET,0)
[1206]Failed to open s-meter.txt.
[1207]s-meter.txt not open.
[1208]The blocking rx output thread did not respond in time. file:rxout.c 
[1209]One or more threads failed to start. file:menu.c
[1210]Failed to reopen par_perseus. File perseus.c
[1211]Frequency out of range, too low, in call to first mixer. file mix1.c
[1212]Frequency out of range, too high, in call to first mixer. file mix1.c
[1213]öÖ
[1214]öÖ
[1215]The Win API function QueryPerformanceFrequency() is not supported
by your hardware platform.
[1216]The Win API function QueryPerformanceCounter() returns an error.
[1217]The selected device for input can not do 16 bit input (or more).
[1218]Specified sound device is already allocated.
[1219]Specified sound device identifier is out of range.
[1220]No device driver is present.
[1221]Unable to allocate or lock memory.
[1222]Attempted to open with an unsupported waveform-audio format.
[1223]Failed to create Event.
[1224]Attempt to pause a thread that was already paused.
[1225]The calibration procedure failed. Data is out of range.
Please try to reproduce this error and report it.
[1226]waveInAddBuffer() failed.
[1227]Failed to open Rx A/D input from soundcard.
Unknown error code.
[1228]Failed to open soundcard for RX input.
The parameter file may specify an unsupported format. Hardware may have
changed or the parameter file is from another computer.
Use "U=A/D and D/A setup for Rx" in the main menu. 
[1229]Failed to close Portaudio Rx input.
[1230]routine:init_eme_database      file:eme.c                      
Failed to read CALL3.TXT  Excessive line length or field too long.
[1231]A/D buffer error.
[1232]waveInAddBuffer() failed.
[1233]waveInAddBuffer() failed.
[1234]waveOutOpen() failed for Rx soundcard output.
[1235]Not enough lines on the screen. Select a larger screen, reduce font
size or reduce the number of soundcards.
[1236]Could not create parameter file in the current directory. 
[1237]The format specified by the ExtIO library is unknown.
[1238]Unable to open sound device for unknown reasons.
[1239]Unknown format specified by the Extio library.
[1240]MEMORY ERROR (bug inside Linrad).
[1241]ERROR. Not enough memory allocated for timf1 (fft1).
Set a narrower bandwidth to make transforms larger.
[1242]The screen size reported by svgalib is smaller than 640 x 480.
Check your par_userint (or remove it) 
Use vgatest to verify that svgalib works ok.
[1243]The screen reported by svgalib is not 256 colours
Check your par_userint (or remove it) 
Use vgatest to verify that svgalib works ok.
[1244]Failed to open serial port. 
[1245]Soundcard input buffer allocation error.
Call to waveInPrepareHeader failed.
[1246]Parameters say the input should be 32 bit
but the system is compiled without 32 bit support.
Rerun A/D setup from the main menu.
[1247]Soundcard input buffer allocation error.
Call to waveInAddBuffer failed.
[1248]Internal error in Linrad. 
Maybe incorrect value for MAX_SVGA_PALETTE
[1249]Could not get socket for network multicasting.
Verify that your network is setup properly. 
[1250]The network is set up to send raw data in 18 bit format
but the raw data is only 16 bit so you can send no more than 16
bits to the network. Use N in the main menu to change the
network settings (or change A/D converter settings to 24/32 bits)
[1251]The network is set up to send raw data in 24 bit format
but the raw data is only 16 bit so you can send no more than 16
bits to the network. Use N in the main menu to change the
network settings (or change A/D converter settings to 24/32 bits)
[1252]The network parameters differ from those saved
in par_userint. (A change was made with N in the main menu
without saving the par_userint file with W afterwards.)
[1253]Illegal value for network flag in file par_userint.
Use 'N' in the main menu and save ui parameters with 'W' afterwards.
[1254]Too many simultaneous network slaves or subslaves.
(You may increase the value of MAX_FREQLIST in globdef.h)
[1255]The device number for one of the soundcards is illegal.
Run "U=A/D and D/A setup for RX" in the main menu to correct the problem. 

In case you are using the TX side of Linrad, you must also
run "V=TX mode setup" in the main menu (B on the sub-menu.)
[1256]Message from sub-master is a list with less than one frequencies.
[1257]Message from sub-master is a list with too many frequencies.
[1258]öÖ
[1259]Calibration function incorrect. (fft1_desired is zero)
[1260]Failed to open D/A output for Tx. 
[1261]Failed to allocate memory for tx buffers.
[1262]Failed to set fragment size for tx microphone input.
[1263]Call to WSAStartup(...) failed.
[1264]Write to network socket returned zero.
[1265]Error in file: par_network. a
Use "N=Network setup" in the main menu to create a new file.
[1266]Error in call to setsockopt. Reusing ADDR failed.
[1267]Failed to bind to network receive address
[1268]Error in attempt to use setsockopt() to request 
that the kernel joins a multicast group.

Multicast floods wifi and many routers. This error may be
caused by a node on your network that does not accept multicast.
A network switch or adjusting multicast filtration settings may solve
the problem.

If you use par_netrec_ip to set your own ip address Linrad does
not check that the address is valid. Use 'N=Network setup'
in the main menu to see what your internet address looks like.
It must be four numbers separated by points like this:
239.255.0.125
All numbers have to be between 0 and 255.
A number above 255 generates this error.
[1269]Waiting for master was interrupted from keyboard.
[1270]Too many simultaneous network slaves.
(You may increase the value of MAX_NETSLAVES in globdef.h)
[1271]open_rx_sndin/snd_pcm_open/error.
[1272]open_rx_sndin:Cannot allocate hardware parameter structure.
[1273]Network connection lost.
[1274]Network read failed.
[1275]Failed bind to socket for network slaves.
[1276]Call to listen(...) on socket for network slaves failed.
[1277]Failed to get serial port options;
[1278]Failed to set serial port options;
[1279]The port number for the serial port is out of range
(1 to 4) in a call to lir_open_serport.
[1280]Call to lir_open_serport failed because of an illegal
baud rate.
[1281]The network has been enabled but the receive mode
you have selcted has not (yet?) been set up.
The network is set to send TIMF2 and/or FFT2 but the mode
you tried to enter does not have those data streams because
the second FFT is disabled.
Restart and press 'T' to disable network transmit.
Then select the processing mode of your choice, press
X, then P, to set the parameters. On the first screen, set 
"Enable second FFT" to 1.
Then exit, press T to enable the network transmit and finally
go to the receive mode of your choice.
[1282]open_rx_sndin:Broken configuration.
No configurations available.
[1283]Read error for microphone input. 
[1284]Could not get socket for receiving UDP from SDR-IP
[1285]Error in call to setsockopt. Resing ADDR failed.

[1286]routine:read_txpar_file      file:tx.c
Failed to allocate scratch memory.
[1287]routine:close_tx_output   file:lsetad.c
Close failed on Tx output from soundcard.
[1288]routine:close_tx_output   file:lsetad.c                      
call to ioctl failed. (SNDCTL_DSP_RESET)
[1289]routine:set_analog_io    file:lsetad.c
No usable device found for loudspeaker output.
[1290]Failed to allocate scratch memory.
[1291]Failed to allocate scratch memory.
[1292]Failed to allocate scratch memory.
[1293]Failed to allocate scratch memory.
[1294]open_rx_sndin:Cannot set access type.
[1296]open_rx_sndin:Cannot set sample format.
[1297]open_rx_sndin:Channels not available for capture.
[1298]open_rx_sndin:resampling setup failed.
[1299]Could not set sample rate.
[1300]open_rx_sndin:Invalid period size.
[1301]open_rx_sndin:Unable to set hw parameters.
[1302]Failed to bind to the SDR-IP address
[1303]Can not open the device for loudspeaker output.
[1304]Can not open the device for loudspeaker output.
[1305]open_rx_sndout:Cannot allocate hw parameter structure for playback.
[1306]open_rx_sndout:Broken configuration: 
no configurations available.
[1307]open_rx_sndout:Cannot set playback access type.
[1308]open_rx_sndout:Cannot set sample format.
[1309]Could not set no of channels for audio output.
[1310]open_rx_sndout:resampling setup failed.
[1311]open_rx_sndout:Could not set sampling speed.
[1312]open_rx_sndout:Unable to set period size for playback.
[1313]open_rx_sndout/snd_pcm_get_params.
Can't recover from underrun - prepare failed.
[1314]routine:make_radar_graph    file:radar.c
Failed to allocate memory for radar.
[1315]Failed to close the Airspy. (Did you disconnect it?.)
[1316]The Extio library can not specify the sampling rate.
[1317]The length of the ExtIO file name exceeds BUFFER_SIZE.
Check par_extio_libname for errors and increase BUFFER_SIZE if 
your file name really needs it.
[1318]open_tx_sndin:Invalid period size.
[1319]Internal error in Linrad.
Please report to me: leif@sm5bsz.com
Save all par*.* files and pack as an archive file (.zip, .bz2, or whatever)
and send those files to me.
To avoid this error, clear the network Rx parameters either
by a manual edit of par_network or by de-selecting network
input in the "N = Network setup" menu.
[1320]lir_empty_da_device_buffer/ writei/ short write
[1321]lir_empty_da_device_buffer/ writei/ catch all error
[1322]err_restart_rxda/ writei/ underrun recovery failed 
[1323]err_restart_rxda/ writei/ short write
[1324]err_restart_rxda/ writei/ catch all error
[1325]open_rx_sndout/ writei/ underrun recovery failed
[1326]open_rx_sndout/ writei/ short write
[1327]open_rx_sndout/ writei/  catch all error
[1328]lir_tx_dawrite/ writei/ short write
[1329]lir_tx_dawrite/ writei/ catch all error
[1330]Sampling rate in par_sdrip not compatible with SDR-IP setup.
Rerun "U=A/D and D/A setup for RX" from the main menu.
[1331]Error in the initialization of soundcard output.
[1332]lir_rx_dawrite/ writei/ catch all error
[1333]Could not find the serial number file for Excalibur.
par_excalibur_sernum
Rerun "U=A/D and D/A setup for RX" from the main menu.
[1334]Error in the par_excalibur_sernum file.
Rerun "U=A/D and D/A setup for RX" from the main menu.
[1335]Failed to open the specified Excalibur device.
Rerun "U=A/D and D/A setup for RX" from the main menu.
[1336]Could not find library function.
Maybe the G31DDCAPI.dll file has been changed?
[1337]The file par_excalibur is corrupted. 
Use "U=A/D and D/A setup for RX" in the main menu to create a new file.
[1338]Sampling rate in par_excalibur not compatible with Excalibur setup.
Rerun "U=A/D and D/A setup for RX" from the main menu.
[1339]Could not set the sampling rate for the Realtek RTL2832 USB dongle.
This should never happen......
[1340]Failed to reset the RTL2832.
[1341]The data type returned from ExtIO.dll (InitHW) is unknown.
[1342]The baseband bandwidth is too narrow for the selected
fft2 storage time. Change one or the other before clicking a signal
after restart.
[1343]An error was reported while reading the SDR-14 or SDR-IQ
[1344]The call to StartHW in the EXtIO library returned zero block size.
[1345]The samplintg speed for SDR-14 or SDR-IQ is incorrect.
Use the U menu to make a new par_sdr14 file. 
[1346]The external hardware can not be controlled by the ExtIO library.
Is hardware connected and powered?
Maybe the opposite sequence InitHW vs SetCallback would work.
[1347]The call to StartHW in the EXtIO library returned a 
negative block size.
[1348]Failed to open the rtl-sdr dongle.
This error is probably caused by incorrect drive routines.
Use Zadig to install a driver:
http://zadig.akeo.ie
[1349]Can not open the framebuffer device.
[1350]Can not read finfo from the framebuffer device.
[1351]Can not read vinfo from the framebuffer device.
[1352]Can not read palette from the framebuffer device.
[1353]Linrad can not handle the framebuffer colour depth. 
[1354]Specify your mouse in /etc/vga/libvga.config
You must specify your mouse type as well as what device to use.
/dev/mouse, /dev/input/mice, /dev/ttyS0, ....  
[1355]Failed to map framebuffer device to memory.
[1356]The file par_rtl2832 is corrupted or not consistent
with other parameters. Use the U menu to set up your USB dongle
and do not forget to press W to save data in the main menu
afterwards. The dongle uses the same crystal for the RF local
oscillator and for the A/D converter so par_userint has to
be compatible with par_rtl2832.
[1357]Failed to open the rtl-sdr dongle.
This might be due to permission problems with libusb.
Try to run as root.
Another module might be loaded for the dongle.
Maybe this command helps:
rmmod dvb_usb_rtl28xxu
If you do not need it, you can blacklist this module.
[1358]Failed to set the RTL2832 on direct sampling mode.
[1359]The file par_pcie9842 is corrupted or not consistent
with other parameters. Use the U menu to set up your PCIe-9842 card
and do not forget to press W to save data in the main menu
afterwards. 
[1360]Failed to allocate buffer for the PCIe-9842 card.
[1361]Unable to open PCIe-9842 card.
Call to WD_Register_Card(...) failed.
Is the kernel driver pci9842.ko loaded??
[1362]Unable to load library.
[1363]Failed to set up buffers for the PCIe9842 card.
Call to WD_AI_ContBufferSetup(...) failed.
[1364]Failed to set up callback routine for PCIe-9842.
Call to WD_AI_EventCallBack(...) failed.
[1365]Can not run Perseus because the libusb-1.0 library has not
been loaded.
[1366]Could not set double buffer mode.
Call to WD_AI_AsyncDblBufferMode(...) failed
[1367]Could not find out how much memory the PCIe driver has.
Call to WD_AI_InitialMemoryAllocated(...) failed
[1368]Could not set the sampling rate for the Mirics USB dongle.
This should never happen......
[1369]Failed to open the bladeRF.
This might be due to permission problems with libusb-1.0.
[1370]Failed to open the bladeRF.
[1371]Failed to get the bladeRF FPGA size.
[1372]Failed to get bladeRF firmware version.
[1373]Call to bladerf_is_fpga_configured() failed.
[1374]The FPGA is not programmed.
Use the program bladeRF-cli to program your FPGA like this:
bladeRF-cli -l <path_to_fgpga_file>
or install it for autoload like this:
bladeRF-cli -L <path_to_fgpga_file>

The FPGA size is 40 K. Look for hostedx40.rbf
[1375]Failed to get the bladeRF FPGA version.
[1376]Could not select signal source.
Call to bladerf_set_sampling() failed.
[1377]The file par_mirics is corrupted or not consistent
with other parameters. Use the U menu to set up your USB dongle
and do not forget to press W to save data in the main menu
afterwards. The dongle uses the same crystal for the RF local
oscillator and for the A/D converter so par_userint has to
be compatible with par_mirics.
[1378]Failed to reset the Mirisdr.
[1379]The file par_bladerf is corrupted or not consistent
with other parameters. Use the U menu to set up your bladeRF
and do not forget to press W to save data in the main menu
[1380]Call to bladerf_is_fpga_configured() failed.
[1381]The FPGA is not programmed.
Use the program bladeRF-cli to program your FPGA like this:
bladeRF-cli -l <path_to_fgpga_file>
or install it for autoload like this:
bladeRF-cli -L <path_to_fgpga_file>
[1382]The call to bladerf_set_sampling() failed.
[1383]The call to bladerf_set_sampling() failed.
[1384]Failed to set sampling speed for bladeRF.
[1385]Failed to set sampling speed for bladeRF.
[1386]Could not set the correct sampling speed for bladeRF.
[1387]The FPGA is not programmed.
Use the program bladeRF-cli to program your FPGA like this:
bladeRF-cli -l <path_to_fgpga_file>
or install it for autoload like this:
bladeRF-cli -L <path_to_fgpga_file>

The FPGA size is 115 K. Look for hostedx115.rbf
[1388]The FPGA is not programmed.
Use the program bladeRF-cli to program your FPGA like this:
bladeRF-cli -l <path_to_fgpga_file>
or install it for autoload like this:
bladeRF-cli -L <path_to_fgpga_file>

The FPGA size could not be determined.
[1389]The file par_afedriusb does not exist, is corrupted or 
not consistent with other parameters.

Use Submenu "D = Set parameters for soundcard radio hardware."
It is under "U=A/D and D/A set up for RX." in the main menu.
[1390]Could not open the Afedri USB control interface.
Afedri device(s) exist but no device is found with the same 
serial number that was selected in the setup. 

Use Submenu "D = Set parameters for soundcard radio hardware."
It is under "U=A/D and D/A set up for RX." in the main menu.

Note that the serial number changes if you change the default
number of channels on Net Afedri.
[1391]setsockopt failed in afedri.c
[1392]setsockopt failed in sdrip.c
[1393]Could not open the Afedri USB control interface.
You need permission to open the USB HID device.
There are several choices:
1) You can run Linrad as root
2) Use chmod as root to change permissions for the device.
3) Create a udev rules file: ..../udev/rules.d/99-afedri.rules
SUBSYSTEM=="hidraw*", ATTRS{idVendor}=="255d",
ATTRS{idProduct}=="0002", MODE="0666"
SUBSYSTEM=="hidraw*", ATTRS{idVendor}=="0483",
ATTRS{idProduct}=="5932", MODE="0666"    
SUBSYSTEM=="hidraw*", ATTRS{idVendor}=="255d",
ATTRS{idProduct}=="0001", MODE="0666" 
SUBSYSTEM=="hidraw*", ATTRS{idVendor}=="255d",
ATTRS{idProduct}=="0006", MODE="0666"
[1394]Could not open the Afedri USB control interface.
No device found.
This may happen if you have not waited long enough after
connecting your Afedri unit.
Try to start Linrad again.
[1395]Could not initialize the ELAD FDM-S1.
Unknown reason. Try co disconnect USB cable and connect again.
[1396]The file par_perseus is corrupted. 
Use "U=A/D and D/A setup for RX" in the main menu to create a new file.
[1397]Sampling rate in par_userint not compatible with FDM-S1 setup.
Rerun "U=A/D and D/A setup for RX" from the main menu.
[1398]Failed to open the Mirics USB unit.
This error is probably caused by incorrect drive routines.
Install the WinUSB driver from libusbx.org
Easiest is to use Zadig.
[1399]Failed to open the Mirics USB unit.
This might be due to permission problems with libusb.
Try to run as root.
Another module might be loaded for the unit.
Maybe one of these commands will help:
rmmod sdr-msi3101
rmmod msi2500
[1400]The file par_airspy is corrupted or not consistent
with other parameters. Use the U menu to set up your USB hardware
and do not forget to press W to save data in the main menu
afterwards. 
[1401]The file par_airspy is corrupted or not consistent
with other parameters. Use the U menu to set up your USB dongle
and do not forget to press W to save data in the main menu
afterwards. 
[1402]Failed to load the libusb-1.0.so library.
[1403]Failed to load the libairspy.so library.
[1404]Failed to set sample rate.
[1405]Failed to set bias T.
[1406]Failed to set sample format.
[1407]Failed to open soundcard for Tx output.
[1408]The transmit output soundcard device number is out of range.
Use 'B' in the 'V=TX mode setup' to select proper device numbers for
the transmit soundcards.
[1409]The transmit input soundcard device number is out of range.
Use 'B' in the 'V=TX mode setup' to select proper device numbers for
the transmit soundcards.
[1410]Failed to open input soundcard for the transmitter.
Use 'B' in the 'V=TX mode setup' to select proper device numbers for
the transmit soundcards.
[1411]Failed to open output soundcard for the transmitter.
Use 'B' in the 'V=TX mode setup' to select proper device numbers for
the transmit soundcards.
[1412]The Perseus library is too old. Remove libperseus-sdr from your system.
To do that, use the command: locate libperseus-sdr.so
then delete the files listed. Typically these files:
/usr/local/lib/libperseus-sdr.so
/usr/local/lib/libperseus-sdr.so.0
/usr/local/lib/libperseus-sdr.so.0.0.0
It is recommended that you remove the libperseus-sdr directory also.
Typically like this:
rm -r /usr/src/libperseus-sdr
Then run this command in the Linrad directory:
./configure --with-help
copy the installation instructions for libperseus-sdr and paste 
them into the command window.
Note that you need root privileges.
[1413]The mirisdr library did not report how many gain levels it 
supports. Install a more modern library.
For Windows, use the latest setup-linrad-dll-package.exe and for Linux,
remove your libmirisdr.so files and run ./configure --with-help
to get instructions on how to install a modern library.
[1414]Something is wrong with your DLL files. 
Linrad will look for DLL files and associated binaries in the
special directory:
C:\Linrad\dll\
Download the file linrad-dll-filesxx.zip and unpack it into the
specified directory.
[1415]Call to Pa_Initialize returned an error.
If this happens on a Windows 10 system on which you have a Delta 44 you have 
to reconfigure the Delta 44. (Reboot or power off does not help.)
Use the M-Audio Delta Control Panel to set the sampling rate to 44100 Hz.
Then use U = A/D and D/A setup in the main menu to select Portaudio
for the soundcard with the ASIO or the WDM-KS driver.

You can select sampling rate, number of channels and number of bits freely.
according to your preferences. The Delta 44 is not locked to 44100, it just
has to inform Windows 10 that it is the default rate.
[1415]Call to Pa_Initialize returned an error.
[1416]Failed to close Portaudio Tx input.
[1417]Failed to close Portaudio Tx output.
[1418]Failed to open soundcard for RX input.
The parameter file might specify an unsupported format. Hardware may have
changed or the parameter file is from another computer.
Use "U=A/D and D/A setup for Rx" in the main menu. 
[1419]Failed to open soundcard for RX input.
The parameter file might specify an unsupported format. Hardware may have
changed or the parameter file is from another computer.
Use "U=A/D and D/A setup for Rx" in the main menu. 
[1420]Could not get device capabilities for rx input soundcard.
[1421]Could not get device capabilities for tx input soundcard.
[1422]Inconsistent soundcard parameters for Windows Tx input.
Number of bits=24, but flag says do not use extended format.
Use 'U' on the main menu to set proper parameters for
your soundcard.
[1423]Could not get device capabilities for rx output soundcard.
[1424]waveOutOpen() failed for Tx soundcard output.
[1425]Could not get device capabilities for rx output soundcard.
[1426]waveInStart returned an error.
[1427]waveInStart returned an error for the second device.
[1428]The transmit setup is incorrect or transmit parameter files missing.
Use the 'V' menu to set up CW and/or SSB.
Do not forget to save at least one file, par_cwproc00 and/or par_ssbproc00.
[1429]A library can not be loaded. 
If you encounter this problem and do not see an obvious reason, please
provide feedback.
[1450]The Rx input thread did not start.
This lasted too long:
thread_status_flag for rx_input_thread not equal THRFLAG_ACTIVE
Probably the requested device is not connected to the computer.
See menu.c
[1451]Error in the parameter file par_sdrip
Use 'U=A/D and D/A setup for Rx' on the main menu to select
the parameters you want - and do not forget to go back to
the main menu to write the new global parameters to disk 
by use of the 'W' command.
[1452]Error in the parameter file par_netafedri
Use 'U=A/D and D/A setup for Rx' on the main menu to select
the parameters you want - and do not forget to go back to
the main menu to write the new global parameters to disk 
by use of the 'W' command.
[1453]Error in the parameter file par_cloudiq
Use 'U=A/D and D/A setup for Rx' on the main menu to select
the parameters you want - and do not forget to go back to
the main menu to write the new global parameters to disk 
by use of the 'W' command.
[1454]No OpenCL platform found. Make sure you have installed
the appropriate packages.
Use clinfo to verify that your drivers are OK.
[1455]Failed to create_clFFT_plan
[1456]Failed clCreateCommandQueue
[1457]GPU is not implemented for receiving timf2 from
the network. Remove your par_xxx file or change 
"First forward FFT version" to a number not using the GPU.
[1458]fft1 version number says use OpenCL but start_ocl has
failed. Try '6' on the main menu.
[1459]fft1 version number says use OpenCL and clFFT but libraries 
are not found.
[1460]fft1 version number says use CUDA but library not present. 
[1461]Failed to create_CUDA_plan
[1462]Failed to execute CUDA plan.
[1463]Failed to set AirspyHF DSP mode.
[1464]Failed to set AirspyHF AGC mode.
[1465]The file par_sdrplay2 is corrupted or not consistent
with other parameters. Use the U menu to set up your USB dongle
and do not forget to press W to save data in the main menu
afterwards.
[1466]Failed to find the SDRPlay device.
[1467]The device failed to start the streaming.
Check all device parameters like, sample rate and frequency.
[1468]Failed to open the SDRPlay USB unit.
This error is probably caused by incorrect drive routines.
Check that nobody else is using the device and the driver
is installed correctly.
[1469]Failed to open the SDRPlay USB unit.
This might be due to permission problems with libusb.
Try to add the user to right group or run as root (BAD).
Another module might be loaded for the unit.
Maybe one of these commands will help:
rmmod sdr-msi3101
rmmod msi2500
[1470]Error saving the par_sdrplay2 file. Check the permission.
[1471]The linrad API and the installed library version is different.
Install the latest library/driver from www.sdrplay.com.
Should work fine with version equal or greater than 2.13
[1472]Memeory allocation error. Enable the dumpfile in
options.h and run again to get information about what went wrong.
[1473]Too low samplingrate in the baseband to initialize
FM low pass filter filter.
[1474]Too low samplingrate in the baseband to initialize
FM low pass filter filter.
[1475]Too low samplingrate in the baseband to initialize
FM low pass filter filter.
[1476]Too low samplingrate in the baseband to initialize
FM low pass filter filter.
[1477]Too low samplingrate in the baseband to initialize
FM low pass filter filter.
[1478]Failed to open soundcard for RX input.
[1479]Call to start Portaudio, but Portaudio already running.
Enable DUMPFILE in options.h to see from where the call comes.
[1480]Call to stopt Portaudio, but Portaudio not running.
Enable DUMPFILE in options.h to see from where the call comes.
[2600]The file par_sdrplay3 is corrupted or not consistent
with other parameters. Use the U menu to set up your RSP device
and do not forget to press W to save data in the main menu
afterwards.
[2601]Something is wrong with the sdrplay_api DLL files.
Linrad will look for DLL files and associated binaries in the
special directory:
C:\Linrad\dll\
The latest SDRplay API DLLs can be downloaded from www.sdrplay.com.
[2602]Error saving the par_sdrplay3 file. Check the permission.
[2610]Something is wrong with the sdrplay_api DLL files.
Linrad will look for DLL files and associated binaries in the
special directory:
C:\Linrad\dll\
The latest SDRplay API DLLs can be downloaded from www.sdrplay.com.
[2611]Failed to open SDRplay API. Make sure the sdrplay_api service
is up and running.
If it is already up, you may want to restart it.
[2612]The API function sdrplay_api_ApiVersion() failed.
[2613]The linrad API and the installed library version are different.
On Windows double check the sdrplay_api.dll (32 and 64 bit) under
C:\Linrad\dll and C:\Linrad\dll\x64.
The latest library/driver can be downloaded from www.sdrplay.com.
[2614]The API function sdrplay_api_DebugEnable() failed.
[2620]The API function sdrplay_api_LockDeviceApi() failed.
[2621]Failed to find the SDRplay device.
[2622]No RSP devices found or available.
Double check the USB connection to the RSP, and make sure it is not
already used by a different application.
[2623]The API function sdrplay_api_SelectDevice() failed.
[2624]The API function sdrplay_api_UnlockDeviceApi() failed.
[2625]The API function sdrplay_api_GetDeviceParams() failed.
[2630]Selected antenna is not compatible with selected RSPduo tuner.
[2640]The device failed to start streaming.
Check all device parameters like sample rate, frequency, and RF/IF
attenuations.
[2650]Unable to set bandwith for RSPduo RX2 in dual tuner mode.
[2651]Unable to set RF attenuation/LNA state for RSPduo RX2 in
dual tuner mode.
[2652]Unable to set IF attenuation for RSPduo RX2 in dual tuner mode.
[2653]Unable to set AGC parameters for RSPduo RX2 in dual tuner mode.
[2654]Unable to set DC offset correction for RSPduo RX2 in
dual tuner mode.
[2655]Unable to set IQ imbalance correction for RSPduo RX2 in
dual tuner mode.
[2656]Unable to set RF/DAB notch filter for RSPduo RX2 in
dual tuner mode.
[2657]Unable to set Bias-T for RSPduo RX2 in dual tuner mode.
[2670]Unable to change RF attenuation/LNA state.
Double check the band and the valid RF attentuation/LNA state values
in the SDRplay API Specification Guide.
[2671]Unable to change passband center frequency.
Make sure it is in the 10kHz-2GHz range.
[2691]The API function sdrplay_api_Uninit() failed.
[2692]The API function sdrplay_api_LockDeviceApi() failed.
[2693]The API function sdrplay_api_ReleaseDevice() failed.
[2694]The API function sdrplay_api_UnlockDeviceApi() failed.
[2695]The API function sdrplay_api_Close() failed.
[3001]Error reported by check cw.
Read file dmp for details.
[3002]